Bath Plumbing 201: Installing a Single-Body Faucet

Now that you have learned how to uninstall the faucet in your bathroom or bedroom, in-bath plumbing 201 it’s time to replace it with the new one! This article will guide you through the installation of a single-body faucet.

Materials You Will Need:

  • Basin Wrench
  • Heat-proof grease
  • Loctite
  • Plumber’s Putty
  • Caulk

Bath Plumbing Instructions:

  • Ensure that you have a clean, uncluttered working area. Cover the area with towels in case of a leak or an over-tightened nut.
  • Remove the foam/plastic gasket. Your faucet will have a ring around the bottom – remove it and replace it with some plumber’s putty. This will ensure that your sink will never leak from the bottom! However, you can skip this step if you are sure that the gasket is waterproof.
  • Lower the faucet onto the counter. Don’t worry about it being 100% in place, right now you will be focusing on inserting the tailpieces. To do this, push them through the holes in the sink area. Then, from underneath the sink, apply the washers and nuts to secure the tailpieces to the bottom. Hand-tighten the nuts until they are tight, and finish with a basin wrench.

Important Bath Plumbing Note:

Remember: it is very important to ensure that you do not over-tighten the nuts.

  • Insert the lift rod into its hole behind the spout. Then, thread the lift rod into the clevis. You will want to push the lift rod past the clevis screw. Push the pivot rod down until the stopper is open, and tighten the clevis to the rod.
  • Using your heat-proof grease, grease the valve stems, located inside the handle where you will screw the handle to the faucet. Then, apply some Loctite to the handle, and tighten the handle screw. Be sure to not over-tighten the screw.
  • Cover each handle with its appropriate temperature icon.
  • Turn the water back on at the stop valves, which should be located underneath the sink. Now you will “test” the faucet to make sure there are no drips or leaks. In order to test for leaks properly, you should first remove the aerator from the spout of the spigot (the little round thing that makes sure the water comes out in a straight stream).
  • Let the water run for a few moments before turning it off to check for leaks or drips. If you don’t see any, now is the time to caulk the sink if you choose. However, this step might be unnecessary, depending on the model of faucet.

Congratulations, you have successfully completed your bath plumbingproject by replacing your bathroom faucet! Do you still have questions? Is DIY bath plumbing not your thing? If so, feel free to contact Total Plumbing Orlando by email or by phone at (407) 435-9807 and we’ll do it for you. Professionals are available 24 hours a day to help with any bath plumbing need you may have.

Bath Plumbing 201: Choosing a New Toilet

If you are ready to upgrade your bath plumbing, toilets have come a long way in the last decade, and have improved significantly, both aesthetically and environmentally. The new generation of toilets have been designed to be more efficient, durable, and less susceptible to clogs than older toilets. In addition, each toilet must pass the 1.6 gallon per flush standard. This challenge has resulted in stronger, shorter flushes, which lead to less water waste.

In today’s bath plumbing market, you have many options when choosing a new commode. Instead of one color and style, you can choose between different types of material such as stainless steel, or unique accessories, such as a bidet.  The style, though, is a top priority, and bath plumbingconsumers should know what to expect when shopping for the right toilet:

Bath Plumbing: Types of Toilets

  • One-piece toilet: One unit that consists of both the bowl and the tank. While the design is seamless, they might be heavier to carry and more difficult to install because of weight.
  • Two-piece toilet: Separated tank and bowl. These are generally easier to carry but may be an eyesore if you prefer a clean, modern look.

Toilets also have a number of characteristics that you may prefer, depending on your lifestyle:

  • Elongated Bowl: Gives the toilet a longer, leaner look, and adds around two inches to the length of the bowl. This type of bowl is great for small children who might have an issue getting up to the toilet without assistance.
  • Elevated Seat: Adds a few inches of height to the toilet. This type of bowl is perfect for elderly or disabled consumers who may find it easier to use a taller seat.

Additional Bath Plumbing Considerations

You can also choose what type of flush you want your toilet to have:

  • Pressure-Assisted: The toilet flush relies on a water pump or compressed air. This option is definitely more expensive than other types of flushing mechanisms; however, the water consumption used when flushing is reduced significantly. This is a great option if you are particularly environmentally friendly.
  • Gravity-Assisted: The tank relies on gravity to flush the toilet. Recent models have taller tanks in order to increase the effectiveness of this method of flushing.

If you want to get really fancy with your bath plumbing, you can choose one of these higher-end options:

  • Bidet: A matching toilet bowl that goes next to the toilet. Many of today’s models offer matching sets and come in many assortments and styles.
  • Dual-Flush Option: gives you the option to choose between an eight-ounce or 1.6 gallon flush.

Toilets today come with more options, accessories, and styles than ever before. However, don’t feel overwhelmed by the plethora of choices! With this bath plumbing information in mind, you will be able to make a sound, educated decision about the best toilet for your home. However, feel free to contact Total Plumbing Orlando by email or by phone at (407) 435-9807 if you have any questions. Our professionals are just a phone call away and are more than happy to help!

Plumbing Leaks Point to a Need for House Repiping

Many people fail to consider plumbing leaks while home shopping because they look at a house as a whole, completed unit unless they either are building a new home or looking to buy a used house.

The prospective homeowner, either of the new or used building, ultimately has to concern themselves with the electrical system, the heating and air-conditioning equipment and the plumbing.

Homeowners often forget about the plumbing until low water pressure or plumbing leaks become evident. Sometimes plumbing leaks are not discovered until the owner gets the current water bill. This is because the majority of the plumbing is hidden from view and leakage may occur in areas that are not normally accessed.

Plumbing leaks in Orlando homes occur for a variety of reasons

Some of the reasons for plumbing leaks are:

· The type of material used in the plumbing system
· The chemical makeup of the water supply
· Installation deficiencies or mistakes
· The normal degradation of the piping over time

How the plumbing materials affect the possibility of plumbing leaks

Plumbers often used galvanized iron piping. The iron pipe had a zinc coating to resist corrosion and rusting. However, the zinc coating degrades over time because it is actually a sacrificial type of coating, bonding with the corrosives and carrying them out of the system.

Polybutylene piping was once call the miracle pipe, seemingly resistant to corrosion and failure. It was discovered, however, that even this piping fell victim to certain chemical compositions in the water and would fail, often in as little as 10 years. Even copper has vulnerabilities and can fail over time.

While plumbing leaks every now and then are expected, if many leaks occur in a relatively short period of time or are in locations other than fittings and joints, it may be a warning sign. Repiping of your home’s plumbing may be necessary to prevent a catastrophic failure and potentially expensive property damage. Be sure to call Total Plumbing Orlando.com as we are licensed experts in whole house repiping work. Reach us at 407-435-9807.

Basic Plumbing Skills: How to Remove a Faucet

Removing the old faucet in your kitchen or bathroom is a relatively simple plumbing job if you have the right tools, instructions, and a little patience.

While you can alwayscontact a professional for any of your plumbing needs, those with a DIY attitude can tackle this project easily.

It is important, though, that you follow these instructions carefully and to have the tools you need on hand to ensure a successful result.

Things You Will Need For Your Plumbing Project:

  • New faucet
  • Locking pliers, adjustable wrench
  • Slip -joint pliers
  • Utility knife
  • Plumber’s putty or silicon caulk
  • Silicon remover or orange cleaner

Instructions For Your Plumbing Project:

  1. Prepare your work area. Clean out the cabinets underneath the sink and lay down towels in case of leakage. A clean workspace will ensure that you have a safe environment and the maximum amount of space to work with. In addition, you will need to turn off the hot and cold water valves.. To make sure all of the water is out of the sink pipes, turn on the faucet and let the remaining water drain out.
  2. Unhook the supply tubes. If the tubes are made of chrome, you will need to replace them. It is possible that you may need to replace the coupling nuts and stops.
  3. Remove the faucet. Loosen the nuts located underneath the sink that are attached to the sprayer hose. You can use slip-joint pliers to remove the nuts if you don’t have very much space. Once you have unscrewed the nuts, you should be able to simply pull the sink out of the basin hole.
  4. Scrape away the caulk. If there is caulk surrounding the sink, use your putty knife to loosen the caulk so you can remove the sink.

Important plumbing tip: Remove all of the caulk from the sink area before installing the new faucet.

Congratulations! You have successfully removed the faucet from your kitchen or bathroom. If you have any questions about this process or need professional plumbing help, contact Total Plumbing Orlando for assistance.

Kitchen Sink Plumbing 101: Choosing a New Kitchen Faucet

A kitchen sink plumbing fact is that a new kitchen faucet can improve the look of your entire kitchen and improve the functionality of your day to day life. Before you buy, there are a few things you should consider. Styles and types range from simple to extravagant, black to white, and one handle to several. Sometimes the best option when taking on kitchen sink plumbing projects is to hire a professional to assist you. However, this is a decision that you can easily make yourself if you have done some research.

The best way to tackle this decision is to blend your personal taste with functionality and durability. Are you a serious chef? A professional-grade spigot might fit your needs best. Do you like a more traditional look? Maybe a two-handled spigot would satisfy your taste. This article on kitchen sink plumbing will help you decide how to choose a new faucet: one that will suit your needs and your style.

Your Most Important Kitchen Sink Plumbing Decision

In order to make the best decision about your new kitchen faucet, you should look at a few important factors. First is to decide between the various styles of faucets available. Single-handle and double-handle devices are the two most common types, though they have accessories and additions you can add if you like.

  • Single handle faucets are generally the most popular because can control the temperature and force of the water coming out with only one hand. They also require fewer holes in your counter, depending on the model.
  • Double-handle faucets have a more traditional look with a handle on each side of the spout for temperature and a separate pull-out sprayer.

Other Kitchen Sink Plumbing Considerations

The finish of the faucet is another aspect to think about when making your kitchen sink plumbing decision. Finishes include bronze, plastic, chrome, brass, plastic, and more. You can choose a finish depending on the style of your kitchen or based on its durability. For example, some faucets come with a special finish that will ensure that the spigot won’t get scratches or tarnish with age.

  • The accessories and extras are a vital part of choosing a faucet. Not only can they improve the functionality of your kitchen, extras can also provide a unique look to your sink.
  • Most will come with a sprayer that may or may not be attached to the spout. This gives you control over the pressure of the water, and when to use a high-powered stream to help clean a stubborn pot.
  • Many models come with an extra dispenser that you can put soap or lotion into to cut down on extra clutter around the sink.
  • Some have the capability to turn on and off by touching the handle or spout. Others have motion sensors so that you don’t have to touch the faucet at all!

Choosing a faucet can be an overwhelming experience. With so many models and styles to choose from, it might seem like you can’t make a decision. However, with this information, you should be able to familiarize yourself with the plethora of options and choose something that best suits your needs and your style. If you have any further questions about choosing a new kitchen faucet, contact us and we’ll be happy to assist  you!

Bath Plumbing 101: How To Replace Your New Toilet in Less Than a Day

bath plumbingReplacing your toilet, a common bath plumbingproject, is easy when you know what to do. Generally, the procedure should take less than a day to finish. By doing it yourself, you can save yourself a substantial amount of money. It’s important, though, to ensure that you follow these instructions carefully so that you don’t accidentally flood your home or shatter the porcelain on your bathroom floor.

If you have any questions about this bath plumbing process, feel free to contact Total Plumbing & Construction at (407) 435-9807. They will be more than happy to answer any queries you may have. If you hit a snag while replacing your commode, Total Plumbing & Construction is available 24/7 to solve any bath plumbing need.

Tools and Materials You’ll Need For This Bath Plumbing Project:

  • Putty knife
  • Wet/Dry Vac
  • Adjustable wrench
  • Screwdriver
  • Replacement toilet
  • Wax ring
  • Closet bolts
  • Silicone caulk
  • Toilet Flange

Instructions:

1. Rule # 1 of bath plumbing projects is to turn off the water supply. If you don’t, you’ll have a lot of cleaning up to do! You will turn the water off at the stop valve the same way you would turn off an outside water faucet. Next, flush the toilet. Let the water drain out of the tank and dry the inside, taking care to get rid of as much water as you can. Using your wrench or pliers, unscrew the coupling nut, which should be located on the bottom of the body of the commode. If you have a wet/dry vacuum, now is the perfect time to utilize it.

2. Remove the bolt nuts inside the tank with a large screwdriver. It is quite possible that the nuts will be stuck; if so, simply apply some penetrating oil to the nuts before trying to remove them. Now you should be able to remove the W.C. from the floor. Take care to discard it somewhere far from your work area, because if you accidentally bump the tank, it will probably break and you’ll have a huge mess on your hands.

3. Remove the bolts from each side of the toilet that are connected to the floor. Again, the nuts will probably be stuck, so use the penetrating oil again if you are unable to unscrew them from the bolt. Once you have removed both of the bolts, you should be able to remove the bowl from the foundation. Be careful as to where you put the bowl – there will be a sticky flange ring coating the bottom of the bowl and it will stick to anything it comes into contact with!

NOTE: you can use a hacksaw to cut the nuts off of the bolt to remove them. However, please be sure to follow all safety precautions and be very careful when using the saw!

4. Remove the wax ring. You can’t miss it – depending on the age of your toilet, it will probably be the grossest part of your bath plumbing project. Take a putty knife and remove the wax ring. Most times the putty comes off in chunks. Make sure to discard of the wax immediately, as it will cling to anything it touches.  Clean the area to get rid of all the excess wax around the flange. Also, remove the tank bolts – you won’t want to use them again.

You will want to plug the hole with a rag or towel so that the fumes from the sewer don’t leak into your home. Ensure that your towel is small enough to fit into the sewer pipe, but long enough that it won’t fall into the hole and clog it.

The best part of bath plumbing: it is time to install your new toilet!

5. Replace toilet flange and tank bolts. If your flange is in good condition, then don’t worry, but it is suggested to not reuse tank bolts. You will insert them into the two openings on the side (the same places in which you removed them when cleaning the toilet flange). Replacing the flange is simple: just unscrew the bolts, and pull off the flange!

6. Apply the wax ring to the underside of the new toilet bowl. You will want to remove the towel you placed in the sewer pipe hole now. After you have the wax ring in place, remove the covering and place it directly onto the pipe opening of the commode (called the “horn”). Make sure that you don’t accidentally touch the wax ring – it will stick to you and make it difficult to keep it on the underside of the bowl.

Note: For the next steps in your bath plumbing project, it is imperative that you take care to not over-tighten the nuts and bolts. Over-tightening can lead to breaking the toilet, which will ruin your whole project and you will have to start over!

7. Lower the new bowl carefully onto the sewer pipe opening. The bolts you replaced will be your guidelines, so this step will be easy. Just take your time, making sure to not accidentally drop the bowl too brusquely or get the wax ring stuck on one of the tank bolts. Once the bowl is installed, put a washer and nut on each of the tank bolts and tighten them. It is easiest to start first with your fingers and to use your pliers to finish tightening. It is important to tighten the nuts alternatively to ensure that the bowl is evenly secured to the floor.

As you near completion of your bath plumbing project, it is time to attach the tank to the toilet bowl. Depending on the model of toilet you purchased, you may have to install the flush valve and the fill valve. If the valves have come preinstalled, skip the next two steps.

8. Attach the flush valve. There should be a place inside the opening of the tank to place the flush valve. After you have installed the flush valve, insert the spud nut into the opening of the tank, with the threaded side facing up. Then tighten the spud nut and place the spud washer onto the nut.

9. Insert and adjust the fill valve. There should be a hole in the back left corner of the new toilet bowl. This is where you will insert the new fill valve. Simply drop the fill valve into the hole (only a small part should stick out of the bottom of the tank) and tighten the nylon lock onto the shaft of the fill valve, first with your fingers, then with pliers.

NOTE: it is important that you tweak the fill valve before installing into the tank to ensure the correct amount of water fills the tank when you flush.

10. Insert tank bolts into bottom of tank. It is important to have the tank lying with its flat side down so that you can properly install the tank bolts. There should be two small openings on the bottom of the tank to insert bolts. First, place a rubber washer over the opening and drop the tank bolt into the hole. Then, from the bottom of the tank, place a brass washer and a nut onto the open end of the bolt and slowly secure it to the tank. Take care to not over-tighten the bolts as they may break the porcelain.

11. Connect the tank to the toilet bowl. There should be two holes to place the tank bolts on the toilet bowl. Carefully slide the tank into place, using the holes for the tank bolts and the spud washer as your guidelines. On the bottom of the holes where you placed your tank bolts, insert a rubber washer, a brass washer, and a nut onto the tank bolt and tighten. It is important that you insert the washers and nuts in this exact order to prevent rust and leakage. Tighten the nuts evenly to ensure proper settling of the tank.

12. Re-attach the water supply to the fill valve. Simply connect the tube to the fill valve the same way you disconnected it in step one. Turn on the water supply and test the toilet to make sure everything works correctly.

13. Caulk the area where the floor touches the commode. This will ensure the toilet won’t leak onto the bathroom floor and prevent the floor from separating from the toilet. Be absolutely certain, though, that the toilet isn’t leaking before you caulk, or your project will be extended significantly because you’ll be scraping at the dried caulk with your putty knife!

14. The last step in your bath plumbing project  is to connect the toilet seat to the bowl. There should be two holes to insert the seat bolts into at the top of the bowl. Attach the nuts and tighten them slowly.

Congratulations! You have successfully completed your bath plumbing project and installed your new commode! If you have any questions about this process, feel free to contact Total Plumbing & Construction at (407) 435-9807.